Bond0 interface doesn't accept MTU higher than 1500.I can set MTU perfectly fine for the slave devices. Recreating the bond0 didn't help to up the MTU.
[ 1626.840818] bond0: Invalid MTU 9000 requested, hw max 1500
[ 1668.913497] ixgbe 0000:05:00.0 enp5s0f0: changing MTU from 1500 to 9000
[ 1669.176015] ixgbe 0000:05:00.0 enp5s0f0: speed changed to 0 for port enp5s0f0
[ 1669.237523] ixgbe 0000:05:00.0 enp5s0f0: detected SFP+: 5
[ 1669.487920] ixgbe 0000:05:00.0 enp5s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[ 1675.591234] ixgbe 0000:05:00.1 enp5s0f1: changing MTU from 1500 to 9000
[ 1675.855232] ixgbe 0000:05:00.1 enp5s0f1: speed changed to 0 for port enp5s0f1
[ 1675.911259] ixgbe 0000:05:00.1 enp5s0f1: detected SFP+: 6
[ 1676.159087] ixgbe 0000:05:00.1 enp5s0f1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[ 1684.745389] bond0: Invalid MTU 9000 requested, hw max 1500
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer3+4 (1)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
System priority: 65535
System MAC address: 90:e2:ba:15:68:20
Active Aggregator Info:
Aggregator ID: 2
Number of ports: 2
Actor Key: 13
Partner Key: 221
Partner Mac Address: 02:1c:73:b2:9a:29
Slave Interface: enp5s0f0
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 90:e2:ba:15:68:20
Slave queue ID: 0
Aggregator ID: 2
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:
system priority: 65535
system mac address: 90:e2:ba:15:68:20
port key: 13
port priority: 255
port number: 1
port state: 61
details partner lacp pdu:
system priority: 32768
system mac address: 02:1c:73:b2:9a:29
oper key: 221
port priority: 16000
port number: 373
port state: 61
Slave Interface: enp5s0f1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 90:e2:ba:15:68:21
Slave queue ID: 0
Aggregator ID: 2
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:
system priority: 65535
system mac address: 90:e2:ba:15:68:20
port key: 13
port priority: 255
port number: 2
port state: 61
details partner lacp pdu:
system priority: 32768
system mac address: 02:1c:73:b2:9a:29
oper key: 221
port priority: 17000
port number: 33141
port state: 61
Settings for enp5s0f0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full 10000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full 10000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0 Transceiver: external Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7) drv probe link
Link detected: yes
Settings for enp5s0f1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full 10000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full 10000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0 Transceiver: external Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7) drv probe link
Link detected: yes
Bond0 interface doesn't accept MTU higher than 1500.I can set MTU perfectly fine for the slave devices. Recreating the bond0 didn't help to up the MTU.
05:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)
05:00.1 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)
[ 1626.840818] bond0: Invalid MTU 9000 requested, hw max 1500
[ 1668.913497] ixgbe 0000:05:00.0 enp5s0f0: changing MTU from 1500 to 9000
[ 1669.176015] ixgbe 0000:05:00.0 enp5s0f0: speed changed to 0 for port enp5s0f0
[ 1669.237523] ixgbe 0000:05:00.0 enp5s0f0: detected SFP+: 5
[ 1669.487920] ixgbe 0000:05:00.0 enp5s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[ 1675.591234] ixgbe 0000:05:00.1 enp5s0f1: changing MTU from 1500 to 9000
[ 1675.855232] ixgbe 0000:05:00.1 enp5s0f1: speed changed to 0 for port enp5s0f1
[ 1675.911259] ixgbe 0000:05:00.1 enp5s0f1: detected SFP+: 6
[ 1676.159087] ixgbe 0000:05:00.1 enp5s0f1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[ 1684.745389] bond0: Invalid MTU 9000 requested, hw max 1500
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer3+4 (1)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
System priority: 65535
System MAC address: 90:e2:ba:15:68:20
Active Aggregator Info:
Aggregator ID: 2
Number of ports: 2
Actor Key: 13
Partner Key: 221
Partner Mac Address: 02:1c:73:b2:9a:29
Slave Interface: enp5s0f0
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 90:e2:ba:15:68:20
Slave queue ID: 0
Aggregator ID: 2
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:
system priority: 65535
system mac address: 90:e2:ba:15:68:20
port key: 13
port priority: 255
port number: 1
port state: 61
details partner lacp pdu:
system priority: 32768
system mac address: 02:1c:73:b2:9a:29
oper key: 221
port priority: 16000
port number: 373
port state: 61
Slave Interface: enp5s0f1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 90:e2:ba:15:68:21
Slave queue ID: 0
Aggregator ID: 2
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:
system priority: 65535
system mac address: 90:e2:ba:15:68:20
port key: 13
port priority: 255
port number: 2
port state: 61
details partner lacp pdu:
system priority: 32768
system mac address: 02:1c:73:b2:9a:29
oper key: 221
port priority: 17000
port number: 33141
port state: 61
Settings for enp5s0f0:
10000baseT/ Full
10000baseT/ Full
Transceiver: external
Auto-negotiati on: on
drv probe link
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
Link detected: yes
Settings for enp5s0f1:
10000baseT/ Full
10000baseT/ Full
Transceiver: external
Auto-negotiati on: on
drv probe link
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
Link detected: yes