I confirm this on Mainboard Gigabyte GA-P35-DS4 with r8169. After resume from S3 speed is 100Mbit/s.
root@k1:/home/kede# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes
The following command brings back 1000Mbit: root@k1:/home/kersten# ethtool -s eth0 speed 1000
The onboard LEDs and the switch indicate 1000 Mbit now. The network-manager-applet from gnome however still shows 100mbit.
root@k1:/home/kersten# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes
I confirm this on Mainboard Gigabyte GA-P35-DS4 with r8169.
After resume from S3 speed is 100Mbit/s.
root@k1:/home/kede# ethtool eth0
100baseT/ Half 100baseT/Full
1000baseT/ Half 1000baseT/Full
100baseT/ Half 100baseT/Full
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
Link detected: yes
The following command brings back 1000Mbit: /home/kersten# ethtool -s eth0 speed 1000
root@k1:
The onboard LEDs and the switch indicate 1000 Mbit now. manager- applet from gnome however still shows 100mbit.
The network-
root@k1: /home/kersten# ethtool eth0
100baseT/ Half 100baseT/Full
1000baseT/ Half 1000baseT/Full
100baseT/ Half 100baseT/Full
1000baseT/ Half 1000baseT/Full
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
Link detected: yes