In this case having either eth0 or eth1 is of no use :(
So need the info. from the sites. If you want me to do something more
lemme know.
You could also try putting up 0.2.0 if you want and I can take a spin at it.
Also in this brief time I've been trying Giplet (less than an hour)
trying to do anything in preferences take a long long time for
Preferences to close.
--
Regards,
Shirish Agarwal
My quotes in this email licensed under CC 3.0 http://creativecommons.org/licenses/by-nc/3.0/ http://flossexperiences.wordpress.com
065C 6D79 A68C E7EA 52B3 8D70 950D 53FB 729A 8B17
Hi Salvatore Bonaccorso,
First of all thank you for trying to get this one right and
taking time to respond on the issue.
I added the PPA and installed it but don't get what I need it.
$ dpkg -l giplet Unknown/ Install/ Remove/ Purge/Hold Not/Inst/ Cfg-files/ Unpacked/ Failed- cfg/Half- inst/trig- aWait/Trig- pend /Hold/Reinst- required/ X=both- problems (Status,Err: uppercase=bad) ======= ======- ======= ======= ==-==== ======= ======= ======= ======= ======= ======= ==
Desired=
| Status=
|/ Err?=(none)
||/ Name Version Description
+++-===
ii giplet 0.1.8-2.intrepid GNOME IP display applet
Now what I'm trying to do is not get the IP from the local interface
but from the websites ""www.getmyip.org whatismyip.org" but not getting it :(
I went to Preferences and in interfaces deleted eth0 and just let
""www.getmyip.org whatismyip.org" therein.
I am using dhcp. Perhaps a look at my ifconfig will tell you what I mean.
shirish@ shirish- desktop: ~$ ifconfig
collisions: 0 txqueuelen:1000
Interrupt: 18 Base address:0xc800
eth0 Link encap:Ethernet HWaddr 00:07:95:44:10:db
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth1 Link encap:Ethernet HWaddr 00:08:a1:92:56:33 a1ff:fe92: 5633/64 Scope:Link
collisions: 0 txqueuelen:1000
Interrupt: 22 Base address:0xcc00
inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::208:
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6397106 errors:0 dropped:0 overruns:0 frame:0
TX packets:6991304 errors:0 dropped:0 overruns:0 carrier:0
RX bytes:4213783164 (4.2 GB) TX bytes:1534493981 (1.5 GB)
lo Link encap:Local Loopback
collisions: 0 txqueuelen:0
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6858 errors:0 dropped:0 overruns:0 frame:0
TX packets:6858 errors:0 dropped:0 overruns:0 carrier:0
RX bytes:1173932 (1.1 MB) TX bytes:1173932 (1.1 MB)
In this case having either eth0 or eth1 is of no use :(
So need the info. from the sites. If you want me to do something more
lemme know.
You could also try putting up 0.2.0 if you want and I can take a spin at it.
Also in this brief time I've been trying Giplet (less than an hour) creativecommons .org/licenses/ by-nc/3. 0/ flossexperience s.wordpress. com
trying to do anything in preferences take a long long time for
Preferences to close.
--
Regards,
Shirish Agarwal
My quotes in this email licensed under CC 3.0
http://
http://
065C 6D79 A68C E7EA 52B3 8D70 950D 53FB 729A 8B17