Comment 35 for bug 285392

softreset failed (device not ready)

Sorry I am providing more information I am hoping I do not have to reinstall there is loads of files on this PC now and to be honest it will be a pain in the butt to redo the system. I hope there is a fix for it

 1.103038] aer 0000:00:06.0:pcie01: service driver aer loaded
[ 1.103045] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.103055] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.103167] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 1.103169] ACPI: Power Button (FF) [PWRF]
[ 1.103212] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.103220] ACPI: Power Button (CM) [PWRB]
[ 1.103402] ACPI: duty_cycle spans bit 4
[ 1.103428] processor ACPI_CPU:00: registered as cooling_device0
[ 1.103455] processor ACPI_CPU:01: registered as cooling_device1
[ 1.105991] isapnp: Scanning for PnP cards...
[ 1.460139] isapnp: No Plug & Play device found
[ 1.469190] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.469306] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.469580] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.470214] brd: module loaded
[ 1.470457] loop: module loaded
[ 1.470510] Fixed MDIO Bus: probed
[ 1.470515] PPP generic driver version 2.4.2
[ 1.470562] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.470585] Driver 'sd' needs updating - please use bus_type methods
[ 1.470592] Driver 'sr' needs updating - please use bus_type methods
[ 1.470621] ahci 0000:00:12.0: version 3.0
[ 1.470639] ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.470667] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
[ 1.470757] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 1.470760] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part
[ 1.471207] scsi0 : ahci
[ 1.471332] scsi1 : ahci
[ 1.471397] scsi2 : ahci
[ 1.471468] scsi3 : ahci
[ 1.471546] ata1: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fff900 irq 22
[ 1.471549] ata2: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fff980 irq 22
[ 1.471552] ata3: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fffa00 irq 22
[ 1.471556] ata4: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fffa80 irq 22
[ 1.952018] ata1: softreset failed (device not ready)
[ 1.952079] ata1: failed due to HW bug, retry pmp=0
[ 2.116033] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.155945] ata1.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
[ 2.155948] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 2.155963] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 2.214260] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 2.214263] ata1.00: configured for UDMA/133