mantic/linux-raspi: 6.5.0-1004.6 -proposed tracker

Boot testing passed, dashboard/swm just need to catch up.

dashboard jenkins shows that all rt tests passed.

This bug was fixed in the package linux-raspi - 6.5.0-1004.6

---------------
linux-raspi (6.5.0-1004.6) mantic; urgency=medium

  * mantic/linux-raspi: 6.5.0-1004.6 -proposed tracker (LP: #2037558)

  * Include USB drivers in linux-modules (LP: #2037938)
    - [Packaging] raspi: Include most USB modules in linux-modules

  * Exclude DRM drivers from linux-modules (LP: #2037936)
    - [Packaging] raspi: Exclude unlikely DRM modules from linux-modules

  * Miscellaneous Ubuntu changes
    - SAUCE: ARM: dts: Fix broken symlinks
    - [Config] raspi: updateconfigs after update to raspberrypi rpi-6.1.y
      (2023-09-29)
    - [Config] raspi: Modify some RP1 configs to fix build failures
    - [Config] raspi: Set ARCH_BRCMSTB=y
    - [Config] raspi: Set IOMMU_SUPPORT=y and BCM2712_IOMMU=y

  * Miscellaneous upstream changes
    - Revert "ASoC: cs43130: Fix numerator/denominator mixup"
    - overlays: Add a sample hat_map
    - Revert "usb: phy: generic: Get the vbus supply"
    - config: 2712: Update defconfig
    - dts: 2712: Update for device tree
    - bcm2708_fb: Hack out dma support
    - gpio_brcmstb: Allow to build for ARCH_BCM2835
    - Allow RESET_BRCMSTB on ARCH_BCM2835
    - pinctrl: bcm2712 pinctrl/pinconf driver
    - vc4/fkms: Remove use of SMI peripheral
    - mmc: brcmstb: add support for BCM2712
    - sdhci: Add SD Express hook
    - Add new "pispbe" driver (though not yet the Makesfiles or DT required to use
      it)
    - irqchip: irq-bcm2712-mip: Support for 2712's MIP
    - reset: reset-brcmstb-rescal: Support shared use
    - net: macb: Also set DMA coherent mask
    - usb: dwc3: Set DMA and coherent masks early
    - drm/panel/raspberrypi-touchscreen: Insert more delays.
    - PCI: brcmstb: Add BCM2712 support
    - V4L2: Add PiSP opaque formats to V4L2
    - V4L2: Add PiSP compressed formats to V4L2
    - bcm2708_fb: Fix more build warnings
    - dt-binding: mfd: Add binding for Raspberry Pi RP1
    - mfd: Add rp1 driver
    - dt-bindings: clock: Add bindings for Raspberry Pi RP1
    - clk: Add rp1 clock driver
    - dt-bindings: pinctrl: Add bindings for Raspberry Pi RP1
    - pinctrl: Add rp1 driver
    - serial: pl011: rp1 uart support
    - mmc: sdhci-of-dwcmshc: define sdio timeout clocks
    - mmc: sdhci-of-dwcmshc: rp1 sdio changes
    - clk: rp1: Add sdio-clk driver
    - i2c: designware: Add SMBUS quick command support
    - dmaengine: dw-axi-dmac: Fixes for RP1
    - spi: dw: Handle combined tx and rx messages
    - pwm: Add support for RP1 PWM
    - drm: Add RP1 DSI driver
    - drm: Add RP1 DPI driver
    - drm: Add RP1 VEC driver
    - v4l2: Add pisp compression format support to v4l2
    - media: rp1: Add CFE (Camera Front End) support
    - dt-bindings: net: cdns,macb: AXI tuning properties
    - ASoC: dwc: Support set_bclk_ratio
    - ASoC: dwc: Add DMACR handling
    - ASOC: dwc: Improve DMA shutdown
    - ASOC: dwc: Fix 16-bit audio handling
    - ASoC: bcm: Remove dependency on BCM2835 I2S
    - hwmon: Add RP1 ADC and temperature driver
    - mfd: bcm2835-pm: Add support for BCM2712
    - soc: bcm: bcm2835-power: Add support for BCM2712
    - drivers: spi: Fix spi-gpio to correctly implement sck-idle-in...

All tasks have been completed and the bug is being closed